Analog Input
Number of Channels: 8
Input Modes: Differential (DIFF), Non-Referenced Single-Ended (NRSE), Referenced Single-Ended (RSE)
ADC Type: Successive Approximation Register (SAR)
Resolution: 16 bits
Conversion Time: 1 µs
Maximum Sampling Rate: 1 MS/s per channel
Input Impedance:
Powered On: 1.25 GΩ ║ 2 pF
Powered Off/Overload: 4.0 kΩ minimum
Input Signal Range: ±1 V, ±2 V, ±5 V, ±10 V (software-selectable)
Input Bias Current: ±5 nA
Input Offset Current: ±5 nA
Input Coupling: DC
Overvoltage Protection:
Powered On: ±42 V maximum
Powered Off: ±35 V maximum
Accuracy (Calibrated):Residual Gain Error: Ranges from 104.4 ppm to 118.4 ppm of reading
Residual Offset Error: 16.4 ppm of range
INL Error: Ranges from 42.52 to 50.52 ppm of range
Absolute Accuracy at Full Scale: Ranges from 252 µV to 2,283 µV
Accuracy (Uncalibrated):
Residual Gain Error: Ranges from 2,921 to 3,021 ppm of reading
Residual Offset Error: Ranges from 631 to 700 ppm of range
INL Error: Ranges from 42.52 to 50.52 ppm of range
Absolute Accuracy at Full Scale: Ranges from 3,769 µV to 36,895 µV
Analog Output
Output Type: Single-ended voltage output
Number of Channels: 8
Resolution: 16 bits
Update Time: 1.0 µs
Maximum Update Rate: 1 MS/s
DAC Type: Enhanced R-2R
Range: ±10 V
Output Coupling: DC
Output Impedance: 0.5 Ω
Current Drive: ±2.5 mA
Overvoltage Protection:
Powered On: ±15 V maximum
Powered Off: ±10 V maximum
Accuracy (Calibrated):
Residual Gain Error: 87.3 ppm of reading
Residual Offset Error: 41.1 ppm of range
INL Error: 61 ppm of range
Absolute Accuracy at Full Scale: 2,498 µV
Accuracy (Uncalibrated):
Residual Gain Error: 2,968.6 ppm of reading
Residual Offset Error: 1,004.1 ppm of range
INL Error: 61 ppm of range
Absolute Accuracy at Full Scale: 40,941 µV
Digital I/O
Number of Channels:
Connector 0: 32 channels, up to 80 MHz
Connector 1: 16 channels, up to 10 MHz
Logic Family: User-selectable, default is 3.3 V
Input/Output Logic Levels: Varies with logic family (e.g., 3.3 V: Input Low Voltage = 0.80 V, Input High Voltage = 2.00 V)
Output Current:
Source: 4.0 mA
Sink: 4.0 mA
Input Leakage Current: ±15 µA maximum
Protection: ±20 V, single line
Digital I/O Voltage Switching Time: 2 ms maximum
FPGA
Type: Kintex-7 160T
Number of Flip-Flops: 202,800
Number of LUTs: 101,400
Embedded Block RAM: 11,700 kbits
Number of DSP48 Slices: 600
Timebase: 40 MHz, 80 MHz, 120 MHz, 160 MHz, or 200 MHz
Timebase Accuracy: ±100 ppm
Bus Interface
USB Compatibility: USB 2.0 Hi-Speed or Full-Speed
Data Transfers: DMA, interrupts, programmed I/O
Number of DMA Channels: 3
Power Requirement
Input Voltage: 9 V to 30 V
Maximum Power: 20 W
Overvoltage Protection: 40 V
Physical Characteristics
Dimensions: 18.5 cm × 17.3 cm × 3.6 cm (7.3 in. × 6.8 in. × 1.4 in.)
Weight: 1,000 g (35.27 oz)
I/O Connectors: 2 × 68-pin VHDCI
Safety Voltages
Channel-to-Earth: ±12 V
Channel-to-Channel: ±24 V
Measurement Category: I
Safety Compliance Standards
Standards Met: IEC 61010-1, EN 61010-1, UL 61010-1, CSA C22.2 No. 61010-1 |
Reviews
There are no reviews yet.